CALL US : +34 (93) 783 30 36   

Technical Racing Products

Los especialistas del MiniZ del radiocontrol

QteQ T plate for MiniZ MR03 102mm [4580299722761]

QteQ T plate for MiniZ MR03 102mmQteQ T plate for MiniZ MR03 102mmQteQ T plate for MiniZ MR03 102mmQteQ T plate for MiniZ MR03 102mmQteQ T plate for MiniZ MR03 102mmQteQ T plate for MiniZ MR03 102mmQteQ T plate for MiniZ MR03 102mm

QteQ T plate for MiniZ MR03 102mm [4580299722761]

Ref: QT-101102-GY

Quantity :

Forma de Pago aceptadas:
Tarjeta de Crédito VISA

Stock updated: 7 h. 58m.

In Stock
Entrega Inmediata

Politica de devoluciones
Politica de envios


QteQ T plate for MiniZ MR03 102mm.

Is a special T bar named 4 balls connect T-Bar set.

Colour Gold.


QTEQ QT-10110198 and QT-101101102 4 Ball Connect T-bar Set Guide

“4 Ball Connect T-bar Set (4BTB)” is intended to use together with either a top oil or

friction shock. As the installation and adjustments require delicate work, please read

these instructions thoroughly before beginning assembly on the 4BTB.

#0 and #1 Phillips screwdrivers are needed to install and adjust “4 Ball Connect T-bar

Set”. Tweezers or pliers may help ease the installation and adjustments. 4BTB

enables users to easily change tweak and roll rigidity of the rear suspension without

having to remove it from the chassis. However, please be mindful that adjustments

must be made in small increments. If you fail to do this, this may lead you into falling

into a pit trap of chassis setting. Please make adjustments one-at-a-time and re-check

the adjustment results each time by running the car on the track, paying special

attention to the effect of the adjustment of 4BTB did on the handling characteristic.

Before changing anything, please drive the car with the stock settings provided on the

4BTB and adjust from here, again in small increments. If chatter occurs at the time of

braking or reversing the car, it would be recommendable to change the damper setting

or limit the rebound stroke of spring unit. When used appropriately, in combination

with a top damper and damper system the 4BTB can support more finely tuned chassis

settings, which expert drivers crave and pursue.

[1] What is included in 4BTB Set

As there are so many tiny parts included in the set, please be careful not to lose them

while checking them up.

These parts are assembled in a T-bar unit:

One T-bar, one Support bar, one O-ring flange and one O-ring

One M1.6 nut, three M2x2 set screws, two M1.6x2.5 countersunk head screws, one

M1.6x4 countersunk head screw

These parts are in pieces:

One Long Ball (L), three Short Balls (S), one Center Block, two M2x8 countersunk

plastic threading screws, two M2x5 countersunk plastic threading screws, two M2x5

countersunk machined screws and one 0.9 hex wrench

[2] Chassis Preparation

Remove T-bar and T-bar base from MR-03 chassis.

Please refer to Image.

[3] 4BTB parts

Assembled T-bar unit

One L Ball

One S Ball

One Center Block

Two M2x8 countersunk plastic threading screws

[4] Center Block

Place the Center Block on the chassis as shown in the image, make sure you notice the

orientation of the part.

There is no need to center it perfectly right now, we will do this in a later step.

[5] Assembled T-bar Unit

While paying attention to not displace the Center Block, set the T-bar unit in the

position as shown in the Image. The Image shows that the Center Block is visible

through the hole of the T-bar unit near the center. Please make sure that your

placement of the unit should be same with that shown in the Image.

[6] Placements of L Ball S Ball

Set the L Ball in the front hole and the S Ball on the rear hole.

At this point, all parts are just set and not yet fixed with screws.

[7] Screw fastening

Use M2x8 countersunk plastic threading screws to secure The L and S Balls. Tighten

them until the screws bottom out and then loosen the slightly. Now move the 4BTB

fore and aft, to ensure it sets right and tighten the screws. It is very important that

you make sure the position of the center block and the S Ball is set right!

[8] Installing the Rear S Balls

Set two S Balls on the holes in the T Bar on the motor mount side.

[9] Screw fastening

When using the original Kyosho Plastic Motor Mounts, fix them with M2x5

countersunk plastic threading screws. For aluminum motor mounts, use the M2x5

countersunk machined screws to secure the Balls in place.

The installation of the 4BTB is now complete, ENJOY!

[10] Adjustments

(Image A) Tighten the screw with the hex wrench to minimize the slop of the 4BTB

within the range where the motor mount moves.

(Image B) Use the two tweak setting screws to adjust for load balance between the

right and left rear tires. In order to engage the tweak screws, make sure that the

screws are barely touching the base. The screws should be kept uniform, and be careful

not to fasten the screws too tight. The tweak adjustment should be made in

increments of about 5 seconds of a second hand on a watch at the maximum.

Tweak adjustment is used to get the car to drive straight under acceleration and allow

the car to have equal steering balance left-to-right.

(Image C) This screw is used to adjust roll rigidity, having a similar function as an

anti-roll bar. Generally speaking, cornering response becomes quicker if the screw is

set tighter, but on the other hand, controlling the car after braking becomes harder.

When setting-up a Mini-z, as body shells have tremendous effect on the roll of the car,

optimal roll rigidities of the machine vary significantly from shell to shell. This screw

would be frequently used to fine-tune the chassis to the appropriate to conditions of

circuit surface, driver and etc. We recommend that the adjustments be made in

increments of 45 degrees.


When will I recive my order?

Correos en Oficina: Si haces el pedido antes de las 12 del mediodia se expedira durante el mismo dia, por lo que estara disponible para recoger a los 2/3 dias de su expedición

Nacex: Si haces el pedido antes de las 18h el pedido se expedira durante el mismo dia y lo recibiras en 24h, a excepción de las poblaciones pequeñas donde Nacex se reserva el derecho de entregar el pedido en 48h

Fedex: Si haces el pedido antes de las 14h el pedido se expedira durante el mismo dia y lo recibiras en 48/72h dependiendo del destino internacional

How much will the shipment cost?

No podemos decirte con exactitud el precio del envio hasta que no sepamos el volumen, peso y destino de tu envio, asi pues la mejor manera de conocer el precio del envio es realizando los pasos de la compra hasta llegar al punto donde la página web cotiza el envio